Key Features:

Large Channel Capacity With Priority Scan
The VXR-9000E may be programmed with up to 32 channels over a wide frequency range and can perform in repeater or base station mode, depending on the application. Includes Priority Channel scanning capability for efficient communications monitoring.

Power Supply Backup With Alert
Should DC power fail at the repeater site, the VXR-9000E will automatically revert to a backup DC power source, if connected. Under backup DC
power, the repeater will transmit an alert message to notify the operator that immediate attention is required at the repeater site.

Flexible, Automatic Command Sequence Configuration
The VXR-9000E may be programmed to perform a five-step sequence of commands for certain operating events. For example, during a DC power failure and the repeater switches to a backup power supply, the repeater can be programmed to switch to low power and send a CW ID advising of the situation, etc.

Designed For High Reliability
The cooling fan diameter is 8 cm and thermostatically controlled to ensure a stable temperature environment for the VXR-9000E. Fan operation may be programmed for three options: off, continuous or temperature-controlled, depending on the application. A malfunction alarm is also included.

Simplex / Duplex Capability
The VXR-9000E is designed for simplex mode with single-antenna operation or full-duplex mode with the optional VXD-60 duplexer when optimal communications is necessary at all times.

Additional Features
• 6 Dual-function programmable keys
• 47 CTCSS tones / 108 DCS codes encode & decode
• Multi-tone decode
• CW ID Transmitter
• CW Message
• Compander per channel
• D-sub 25 pin accessory connector
• Automatic DC backup switching w/alert
• EIA rack mount size

 

 

Vertex Standard VXR-9000 Repeater Specifications

General Specifications
Frequency Range	VHF: 134 - 160 MHz (A), 146 - 174 MHz (C) UHF: 400 - 430 MHz (A), 440 - 470 MHz (CS)
Number of Channels	32
Power Supply Voltage	13.6 V DC ± 10%
Channel Spacing	12.5 / 20 / 25 kHz
PLL Steps	2.5 / 5.0 / 6.25 kHz
Operating Temperature Range	-30ºC to +60ºC
Frequency Stability	1.5 ppm, 1.0 ppm (30 min. after wake up)
RF Input-Output Impedance	50 Ohms
Dimension (H x W x D)	483 x 88 x 343 mm
Weight (Approx.)	9.7 kg
Receiver Specification: measured by EN 300 086
Sensitivity 20dB SINAD	-4 dBμV emf
Selectivity	70 dB / 60 dB
Intermodulation	70 dB
Spurious and Image Rejection	57 dBm
Squelch Threshold	0.4 μV (adjustable)
Audio Distortion	< 3 %
Conducted Spurious	< -90 dB
Hum and Noise	> 50 dB
Audio Frequency Response	De-emphasis 6 dB/oct (from 300 Hz to 3 kHz)
Antenna Connector	BNC
Audio Output	4 W @ 4 Ohms
Transmitter Specification: measured by EN 300 086
RF Output	25 / 10 / 5 W
Duty Cycle	50%
Modulation	16K0F3E, 11K0F3E
Modulation Limiting	±5.0 kHz / ±2.5 kHz
Hum and Noise	> 50 dB (Wide), > 45 dB (Narrow)
Microphone Sensitivity	5 mV
Antenna Connector	Type-N
Audio Distortion	< 2.5% @ 1kHz
Spurious Emission	-36 dBm @ ≤ 1 GHz, -30 dBm @ > 1 GHz